网纵论坛

标题: ROS+流控分流详细设置方案 [打印本页]

作者: yucheng 时间: 2014-3-22 15:54
标题: ROS+流控分流详细设置方案
基于带宽环境（联通100M，6条20M ADSL），把联通作为默认线路，AD做分流为客户配置策略。

ROS配置
先为联通线路配上IP，routes，DNS，NAT转发
/ip address
add address=218.1.1.2/29 broadcast=218.1.1.55 comment="\C1\AA\CD\A8100M" \
disabled=no interface=unicom network=218.1.1.48
/ip route
add comment="" disabled=no distance=1 dst-address=0.0.0.0/0 gateway=218.1.1.54 scope=30 target-scope=10
/ip dns
set allow-remote-requests=yes cache-max-ttl=1w cache-size=512KiB max-udp-packet-size=50 servers=222.1.1.85,222.1.1.88
/ip firewall nat
add action=masquerade chain=srcnat comment="" disabled=no
为AD做pcc并加上分流ip（192.168.1.100）
/ip firewall mangle
add action=change-mss chain=forward comment="" disabled=no new-mss=1440 \
protocol=tcp tcp-flags=syn tcp-mss=1441-65535
add action=mark-connection chain=prerouting comment="" disabled=no \
new-connection-mark=con1 passthrough=yes per-connection-classifier=\
both-addresses:6/0 src-address=192.168.1.100
add action=mark-routing chain=prerouting comment="" connection-mark=con1 \
disabled=no new-routing-mark=rou1 passthrough=no src-address=\
192.168.1.100
add action=mark-connection chain=prerouting comment="" disabled=no \
new-connection-mark=con2 passthrough=yes per-connection-classifier=\
both-addresses:6/1 src-address=192.168.1.100
add action=mark-routing chain=prerouting comment="" connection-mark=con2 \
disabled=no new-routing-mark=rou2 passthrough=no src-address=\
192.168.1.100
add action=mark-connection chain=prerouting comment="" disabled=no \
new-connection-mark=con3 passthrough=yes per-connection-classifier=\
both-addresses:6/2 src-address=192.168.1.100
add action=mark-routing chain=prerouting comment="" connection-mark=con3 \
disabled=no new-routing-mark=rou3 passthrough=no src-address=\
192.168.1.100
add action=mark-connection chain=prerouting comment="" disabled=no \
new-connection-mark=con4 passthrough=yes per-connection-classifier=\
both-addresses:6/3 src-address=192.168.1.100
add action=mark-routing chain=prerouting comment="" connection-mark=con4 \
disabled=no new-routing-mark=rou4 passthrough=no src-address=\
192.168.1.100
add action=mark-connection chain=prerouting comment="" disabled=no \
new-connection-mark=con5 passthrough=yes per-connection-classifier=\
both-addresses:6/4 src-address=192.168.1.100
add action=mark-routing chain=prerouting comment="" connection-mark=con5 \
disabled=no new-routing-mark=rou5 passthrough=no src-address=\
192.168.1.100
add action=mark-connection chain=prerouting comment="" disabled=no \
new-connection-mark=con6 passthrough=yes per-connection-classifier=\
both-addresses:6/5 src-address=192.168.1.100
add action=mark-routing chain=prerouting comment="" connection-mark=con6 \
disabled=no new-routing-mark=rou6 passthrough=no src-address=\
　　192.168.1.100
/ip route
add comment="" disabled=no distance=1 dst-address=0.0.0.0/0 gateway=\
pppoe-out1 routing-mark=rou1 scope=30 target-scope=10
add comment="" disabled=no distance=1 dst-address=0.0.0.0/0 gateway=\
pppoe-out2 routing-mark=rou2 scope=30 target-scope=10
add comment="" disabled=no distance=1 dst-address=0.0.0.0/0 gateway=\
pppoe-out3 routing-mark=rou3 scope=30 target-scope=10
add comment="" disabled=no distance=1 dst-address=0.0.0.0/0 gateway=\
pppoe-out6 routing-mark=rou6 scope=30 target-scope=10
add comment="" disabled=no distance=1 dst-address=0.0.0.0/0 gateway=\
pppoe-out5 routing-mark=rou5 scope=30 target-scope=10
add comment="" disabled=no distance=1 dst-address=0.0.0.0/0 gateway=\
　　pppoe-out4 routing-mark=rou4 scope=30 target-scope=10

配置内网lan IP
/ip address
add address=192.168.1.1/24 broadcast=192.168.1.255 comment="added by setup" \
　　disabled=no interface=lan network=192.168.1.0

接下来做流控配置
流控接线：ros lan口接流控外网口，流控内网口接核心交换机，流控管理口接核心交换机。
管理口设置为192.168.1.105，掩码255.255.255.0.

增加分流代理，192.168.1.100 网关192.168.1.1

然后用策略向导增加策略。详细步骤请点流控大师--策略向导
http://bbs.netzone.com/thread-1170-1-1.html

PS,建议在所有地址都确保正后调用策略，否则分流失败会导致分流的应用无法正常联网

作者: 呦呦妹子05 时间: 2017-7-18 16:39

国外uu,国产uu最新地址开放注册了,网站难找

iujlb.com

欢迎光临网纵论坛 (http://v.netzone.com/)